Skip to content
The number one comparison site for certification in the Netherlands

ISO 9001 requirements by clause

The requirements of ISO 9001 are in clauses 4 to 10 of the standard. Those clauses cover context, leadership, planning, support, operation, evaluation and improvement. The edition that applies now is ISO 9001:2026. ISO published it on 16 September 2026. Certificates on ISO 9001:2015 remain valid until 30 September 2029. A requirement that genuinely does not apply within your scope may be designated as not applicable. Design and development is an example. That is only allowed if you justify it and if it does not affect your ability to provide good products and services.

Compare certification bodies for ISO 9001
On this page
  1. Structure of the ISO 9001 requirements
  2. Current edition of ISO 9001
  3. Excluding an ISO 9001 requirement that does not apply
  4. ISO 9001 requirements and the choice of your certification body

The requirements of ISO 9001 are set out in a formal standard text of seven clauses. What does a company of ten people really have to do for them? After reading this article you will know how the requirements are structured, what each clause asks of you, which edition applies, when you may exclude a requirement and how the requirements affect your choice of certification body.

Structure of the ISO 9001 requirements

The requirements for your company are in clauses 4 to 10. They say what you must arrange. How you do that is up to you. Clauses 1 to 3 only describe what the standard is about. They also give the terms the standard uses. Those seven clauses follow the fixed structure that ISO uses for all management system standards. That is called the harmonised structure. At the back, annex A explains the terms. It also explains the intent of the requirements.

The introduction of the standard (0.3.2) maps the clauses onto the cycle of planning, doing, checking and adjusting (PDCA). Clause 4 describes your context. It also describes what goes into the cycle. Clause 6 is planning. Clauses 7 and 8 are doing. They also describe what you need for that. Clause 9 is checking. Clause 10 is improving. Leadership (clause 5) is in the middle. The reason is that top management supports the whole cycle. Which documents you have to record for this is in the mandatory documents for ISO 9001.

Clause 4 of ISO 9001: context of your organisation

Clause 4 asks that you know the environment you work in. You also know what within it falls under your quality system. You determine which matters inside and outside your company affect your quality. You also determine whether climate change plays a role for you. You determine who has an interest in your work, such as customers, suppliers and regulators. You also determine what they ask of you. Then you record what falls under the system. That is called the scope. You also record which processes you need. And how they connect with each other.

In practice the auditor wants to see that you can explain this. It must also match what the auditor sees in your company. An installation company that installs more and more heat pumps should, for example, mention the new requirements of customers. It should also mention the availability of fitters.

Clause 5 of ISO 9001: leadership

Clause 5 places responsibility for quality with top management. Management draws up a quality policy. That policy fits the direction of the company. Management ensures that the customer is central. It also assigns who is responsible for what. This also includes management promoting a quality culture and ethical behaviour. That way everyone contributes to a system that works.

The auditor therefore wants to hear from management itself how it takes decisions about quality. The auditor also wants to know whether the policy says anything about your company. Or could it just as well have hung on the wall next door?

Clause 6 of ISO 9001: planning

Clause 6 asks that you look ahead. You determine which risks and opportunities exist. You also determine what you do with each of them. You set quality objectives that you can measure. You record who does what and when. And you plan changes to the system before you make them.

An objective such as "keeping customers satisfied" is too vague for the auditor. "Fewer than 2% of handovers with a complaint" can be measured. Then it can be seen whether you achieve it.

Clause 7 of ISO 9001: support

Clause 7 is about everything you need to do the work well. That means people, buildings and tools. It is also about a suitable working environment. It further covers measuring equipment that is accurate. And the knowledge that is in your company. You ensure that people are competent for their work. You also ensure that they know what is expected of them. That also applies to quality culture and ethical behaviour. You also arrange communication. And you control the documents you record.

Here the auditor often asks an employee on the shop floor what the quality policy means for their own work. For a measuring instrument the auditor checks whether it has been calibrated or verified.

Clause 8 of ISO 9001: operation

Clause 8 is the largest clause. It follows the route of an order through your company. It starts with planning your work. It also starts with establishing what the customer asks for. Then you check whether you can deliver that before you say yes. Then come design and development of products and services. Then comes the control of what suppliers and subcontractors do for you. Then comes carrying out the work under controlled conditions. And then comes the care for the customer's property or data. It ends with the check before something goes to the customer. It also ends with what you do if something is not right. That way it does not reach the customer unnoticed.

Here an auditor often follows one real order, from quote to handover. At each step the auditor checks whether you do what you have agreed.

Clause 9 of ISO 9001: performance evaluation

Clause 9 asks that you check for yourself whether the system works. You measure what matters. That includes how satisfied customers are. You analyse those figures. You hold an internal audit. In it you have your own system checked. You also hold a management review. That is a fixed moment at which management checks whether the system does what it should. Management also looks at what needs to improve.

In stage 1 of the certification audit the auditor checks whether both are planned and under way. In stage 2 the auditor assesses them again. So plan them before stage 1. Complete them before stage 2.

Clause 10 of ISO 9001: improvement

Clause 10 asks that you tackle errors at the root cause. You also keep improving. Does something go wrong or does a complaint come in? Then you solve it immediately. You find out why it happened. You take a measure that prevents recurrence. After that you check whether that measure worked.

Does an installer keep getting the same complaint about forgotten handover documents? Then the auditor wants to see the complaint, and also the cause. In addition the auditor wants to see evidence that it no longer happens afterwards. A thicker manual does not solve that.

Current edition of ISO 9001

The edition that applies now is ISO 9001:2026. ISO published it on 16 September 2026. It replaces the 2015 version. A certificate on ISO 9001:2015 remains valid until 30 September 2029. What differs between the two is in the transition to ISO 9001:2026. In the Netherlands you buy the standard from NEN (the Dutch standardisation institute). It is called NEN-EN-ISO 9001:2026, also in Dutch.

Excluding an ISO 9001 requirement that does not apply

You may designate a requirement as not applicable. That is allowed if it genuinely does not apply within your scope. You must justify it, though. It also must not affect your ability to deliver good products and services and to satisfy customers. Since 2015 ISO 9001 no longer has a list of permitted exclusions. The starting point is that every requirement applies. The auditor checks whether your justification is sound. What you exclude and why, you record in your scope. The certificate itself describes your activities.

Examples that ISO and IAF themselves give to auditors:

  • Measuring equipment. A hairdresser without measuring instruments does not need to arrange anything for the traceability of measurements.
  • Property of others. A company that never holds goods or data of customers or suppliers does not need to arrange care for them.
  • Design and development. A company receives its products and services ready-made from a parent company or from the customer. It develops nothing in them itself. Such a company does not design.

Design and development is where things often go wrong. It also applies to services. Anyone who determines what a service or product looks like is designing. A training provider that creates a new course is therefore designing. You can also exclude part of those requirements instead of all of them. Do you have a product that has been the same for years? Then at least the requirements for controlling design changes apply. They apply as soon as you change something.

In two situations the auditor does not accept an exclusion:

  • Outsourced work. A requirement does not lapse because someone else does the work for you. Do you outsource design? Then you remain responsible. Then you must show how you control that design work. Your scope may then state "control of outsourced design". That is only allowed if you have evidence of it.
  • A requirement that affects your customer. Does leaving out a requirement affect the quality your customer receives? Then you may not say that you comply with ISO 9001. You must then still fulfil the requirement before your certificate is issued.

Your scope is not forever. Does a construction company that only builds get a contract in which it is also responsible for the design? Then it includes design in its system. It also reports this to the certification body. When the project is finished, the scope can go back.

ISO 9001 requirements and the choice of your certification body

Your scope determines what will be stated on your certificate. In that way it also determines which certification body may certify you. The text on the certificate must describe your activities, products and services per site. That text must not be misleading. Does it say "design and installation"? Then you must show that you design. For ISO 9001 a certification body is approved per sector. That works through the sector codes (IAF codes) in the accreditation. A certification body that does not have your sector in its accreditation cannot give you an accredited ISO 9001 certificate.

In your request for quotes, state what falls under your system. Also state which requirements are not applicable. Then every certification body calculates with the same data. That way quotes are comparable. The number of audit days depends on what the certification body has to assess. And so do the costs of ISO 9001. At CertificeerWijzer you do this once. That applies to several certification bodies that may certify ISO 9001 for your sector.

Sources

  1. ISO, ISO 9001:2026, what businesses need to know iso.org
  2. ISO/TC 176/SC 2, ISO 9001:2026 has been released committee.iso.org
  3. ISO 9001:2015, introduction 0.3.2 and figure 2 (PDCA and the clauses), Online Browsing Platform iso.org
  4. NEN, NEN-EN-ISO 9001:2026 nl nen.nl
  5. ISO 9001 Auditing Practices Group (ISO and IAF), Scope and applicability, edition 3, 1 December 2023 committee.iso.org
  6. ISO 9001 Auditing Practices Group (ISO and IAF), Design and development process, 13 January 2016 committee.iso.org
  7. UKAS, Technical Bulletin, Auditing of design activities in ISO 9001 scopes, 11 January 2021 ukas.com
  8. IAS, summary of ISO/IEC 17021-1:2015 section 9 iasonline.org
  9. RvA, ASR103 accreditation of certification bodies for management systems rva.nl
  10. UKAS, Technical Bulletin, Quality Management Systems (QMS) ISO 9001:2026 Transition ukas.com