Skip to content
The number one comparison site for certification in the Netherlands

All about ISO 45001

ISO 45001 is the international standard for an occupational health and safety management system. The standard is voluntary. The RI&E (risk inventory and evaluation) under the Arbowet (Dutch Working Conditions Act) is mandatory, however, and often forms the basis. You get the certificate from an accredited certification body that has your sector in its accreditation. On 24 September 2026 CertificeerWijzer counted 12 certification bodies for ISO 45001 in the Netherlands. All 12 may cover construction, 6 may cover healthcare. A construction company of 10 FTE needs 3.5 days for the initial audit, against 2 days for ISO 9001. An audit day costs €1,000 to €1,800 excluding VAT.

Compare certification bodies for ISO 45001
On this page
  1. What is ISO 45001?
  2. Who is ISO 45001 for and is it mandatory?
  3. What does ISO 45001 require?
  4. Steps and lead time of ISO 45001 certification
  5. What does ISO 45001 cost?
  6. Transferring and the new version of ISO 45001
  7. Who may certify ISO 45001?
  8. Related standards of ISO 45001

Worldwide there were more than 540,000 valid ISO 45001 certificates in 2024. But what does the standard actually ask of your company, and do you need it if you already have an RI&E or VCA? After reading this article you will know what ISO 45001 is, who it is meant for, what it requires, how long the process takes, what it costs and who may certify it.

What is ISO 45001?

ISO 45001 is the international standard for an occupational health and safety management system. Such a system helps you prevent accidents and work-related ill health, and improve your approach every year. The standard says which arrangements you must make. How you fill them in is up to you. So a cleaning company and a concrete plant can both hold a certificate. Only for ISO 9001 and ISO 14001 have more certificates been issued. That puts ISO 45001 in third place among the management system standards.

ISO 45001 works with the same cycle as other ISO standards: plan, do, check and act (PDCA). The standard puts the emphasis on the involvement of management and on the participation of workers. It also asks you to map hazards, comply with the occupational health and safety laws and be prepared for emergencies. The version that applies now is ISO 45001:2018, with an amendment on climate change from 2024. In the Netherlands the standard is called NEN-EN-ISO 45001. In 2018 ISO 45001 replaced the British standard OHSAS 18001.

Who is ISO 45001 for and is it mandatory?

ISO 45001 is voluntary. The standard is for every organisation, of any size and in any sector. ISO calls it especially valuable in sectors with higher risks, such as construction, manufacturing and agriculture. Companies get the certificate for these reasons:

  • Own improvement. Many companies want fewer accidents and less sickness absence. The annual audit keeps attention focused.
  • Clients. Large clients and main contractors sometimes ask it of their suppliers and subcontractors.
  • Tenders. In government tenders certification is often a requirement. Check in the documents which standard the contracting authority asks for. What a contracting authority may require is explained in certificate for a tender.

The risk inventory and evaluation (RI&E) is mandatory, however, even without ISO 45001. That is set out in article 5 of the Arbeidsomstandighedenwet (Dutch Working Conditions Act). In it every employer records in writing which risks the work involves, with a plan of action. ISO 45001 does not replace that duty. The RI&E is, however, a logical starting point for your system. Many construction and installation companies also have VCA. What the difference is, is explained in what VCA is.

What does ISO 45001 require?

ISO 45001 asks you to control the risks to your people and to keep improving. The requirements are in clauses 4 to 10 of the standard. In plain language they ask that you:

  • know which matters inside and outside your company affect your occupational health and safety policy;
  • as management take responsibility and let your people have their say;
  • find hazards, assess risks and know which occupational health and safety laws apply to you;
  • take measures, also for changes, purchasing, contracted work and emergencies;
  • measure whether you meet your objectives and whether you comply with the law, with an internal audit and a management review;
  • investigate incidents, such as accidents and near misses, and tackle the cause.

Take an installation company where technicians almost fall off a ladder twice. ISO 45001 does not then ask for a new binder. The installation company records both reports and looks for the cause. After that it adjusts the way of working and checks whether that works. All requirements are listed in the requirements of ISO 45001. Which documents you need is explained in the mandatory documents.

Steps and lead time of ISO 45001 certification

Starting from scratch, an ISO 45001 process takes about eight months. Count on three to four months of that between your order and the first audit. Do you already work in a structured way, for example with VCA or ISO 9001? Then it takes four to five months. The certification audit has two parts, stage 1 and stage 2. In stage 1 the auditor checks whether your system is complete enough to assess. In stage 2 the auditor checks whether the system works on the shop floor. For ISO 45001 that requires a visit to your workplace. Every step is explained in the steps to ISO 45001.

What does ISO 45001 cost?

A certification body charges the number of audit days times its own day rate. An audit day is a working day of about eight hours of an auditor. The rate lies between €1,000 and €1,800 excluding VAT. How many days you need is set out in an international calculation table: Global ACI-TECH-3-004 (IAF MD 5).

For ISO 45001 it depends on your number of people and on the occupational health and safety risk of your work. Construction counts as high risk, office work as low. Subcontractors who work under your control or influence also count.

An installation company of 4 FTE needs 3 days for the initial audit. That is €3,000 to €5,400 excluding VAT. A construction company of 10 FTE needs 3.5 days for the initial audit and 1 day for each surveillance audit. For the initial audit and two surveillance audits together, that is €5,500 to €9,900 excluding VAT. For ISO 9001 the same calculation table gives that company 2 days for the initial audit. The table and the calculation rules are in the costs of ISO 45001.

Transferring and the new version of ISO 45001

Do you already have an ISO 45001 certificate? Then you can transfer to another certification body at any time. You do not have to start over. The new certification body must, however, have your sector code in its own accreditation. The rule document for transferring, Global ACI-TECH-3-002 (IAF MD 2), requires this.

ISO is working on a new version of the standard. The draft (ISO/DIS 45001) went to ballot in June 2026. ISO plans the new version as ISO 45001:2027. There is no transition period yet. Until the new version is published, you certify against ISO 45001:2018.

Who may certify ISO 45001?

Only a certification body approved by the Dutch accreditation body or a foreign sister organisation may certify ISO 45001 under accreditation. On 24 September 2026 CertificeerWijzer counted 12 certification bodies in the Netherlands with such an accreditation for ISO 45001. Of these, 8 hold their accreditation through the Dutch accreditation body. Four hold it only through UKAS, the British sister organisation of the Dutch accreditation body.

For ISO 45001 your sector also counts. The accreditation runs per sector code (IAF code). The rule document for occupational health and safety certification, Global ACI-TECH-3-016 (IAF MD 22), uses the same 39 sectors for this as ISO 9001 and ISO 14001. For each sector it names the hazards that often occur there. A certification body may only issue an accredited certificate for the sectors in that accreditation:

Reference date 24 September 2026Certification bodies
All 39 sectors 2 of the 12
At most 8 sectors 4 of the 12
Construction (code 28) 12 of the 12
Transport (code 31) 7 of the 12
Healthcare (code 38) 6 of the 12

So a construction company can go to any certification body. A healthcare institution has half the choice, while healthcare belongs to the highest occupational health and safety risk in the calculation table.

Choosing an ISO 45001 certification body

Every certification body calculates with the same table. Yet they often arrive at a different number of days. So pay attention to these points:

  • Sector. All your sectors are in the accreditation of the certification body.
  • Risk category. The certification body shows which category you are placed in and how the number of days is arrived at.
  • Auditor. You hear what experience the auditor has in your sector.
  • Subcontractors and projects. The certification body says how people from subcontractors count and how many construction sites or project locations get a visit.
  • Total over three years. Compare the initial audit, two surveillance audits and the recertification together.
  • Combination. Do you also have ISO 9001, ISO 14001 or VCA? Ask whether the certification body may also cover those, for your sector.

More points to choose on are in choosing a certification body. The full overview is in certification bodies. Through CertificeerWijzer, certification bodies that may cover your sector receive the same details. Then you see side by side who chooses which risk category.

ISO 45001 shares its structure with other ISO management system standards. That lets you combine them in one system and one audit:

  • ISO 9001 is the standard for quality management.
  • ISO 14001 is the standard for environmental management. Together with ISO 45001 it often forms one system for health, safety and environment.
  • VCA is a safety certification that many contractors and installation companies have. The difference is explained in what VCA is.

Sources

  1. ISO, ISO 45001:2018 Occupational health and safety management systems (status, amendment, successor, FAQ) iso.org
  2. ISO/TC 283, news about the revision of ISO 45001 committee.iso.org
  3. ISO Survey 2024, infographic globalstd.com
  4. Arbeidsomstandighedenwet (Dutch Working Conditions Act), article 5 wetten.overheid.nl
  5. Ondernemersplein (KVK, Netherlands Chamber of Commerce), ISO and NEN certification for your business ondernemersplein.overheid.nl
  6. Global ACI-TECH-3-004 (M) version 1.0, Determination of Audit Time (was IAF MD 5:2023) sys.global-aci.org
  7. Global ACI-TECH-3-016 (M) version 1.0, Application of ISO/IEC 17021-1 for the Certification of OH&SMS (was IAF MD 22:2023) sys.global-aci.org
  8. Global ACI-TECH-3-002 (M) version 1.0, Transfer of Accredited Certification of Management Systems (was IAF MD 2:2023) sys.global-aci.org
  9. Global ACI, IAF and ILAC Document Cross-Reference Table v14.0 sys.global-aci.org
  10. RvA, all accredited bodies for ISO/IEC 17021-1 rva.nl